Guide
The Machine Vision Project Checklist
What does a typical machine vision project look like? How long does it take? What do I need to consider to get the right solution?
Calculator
ROI Calculator for Machine Vision
Fill out the Excel sheet and find out what ROI you can expect from your machine vision project.
Guide
An introduction to Machine Learning in Vision Projects
Get an introduction to the latest trends in machine vision and learn why inspection with machine learning is so effective.
Our Blog About Advanced Machine Vision
Vision Insights & Inspiration
-
December 12, 2024 What to expect from machine vision in 2025 -
December 12, 2024 The cost and ROI of an automated surface... -
October 10, 2024 How hyperspectral imaging can reveal the invisible -
June 06, 2024 Achieve extraordinary flexibility with a new... -
March 03, 2024 Solving complex inspection problems with an... -
March 03, 2024 How AI is helping us take surface inspection to...
Learn From Our Experts
The Vision Lab
-
November 11, 2024 [The vision lab #30] How we use fluorescence to... -
November 11, 2024 [The Vision Lab #29] 4 methods for 3D inspection... -
November 11, 2024 [The Vision Lab #28] Surface Control AI -... -
October 10, 2024 [The vision lab #27] How to make multiple vision... -
September 09, 2024 [The Vision Lab #26] The challenges of automating... -
August 08, 2024 [The Vision Lab #25] Robot Sampling can solve...
Datasheets
.jpg?width=3000&height=1974&name=Inline%20tube%20inspection%20(1).jpg)
Inline Tube-Inspection
Vision systems used for inspection of pharmaceutical and technical glass production.
Designed and developed to meet high demands for speed and sensitivity.
Designed and developed to meet high demands for speed and sensitivity.
Clever Cutting
The production of glass tubes is a wasteful procedure, but Clever Cutting can help you improve the yield considerably.
Reduce waste by up to 40%
Reduce waste by up to 40%
Hot End Tableware Inspector
The JLI Tableware inspection system is designed for use in both the hot and cold-end of the production line.
The system will continuously measure and inspect tableware as the glasses pass on a conveyor.
The system will continuously measure and inspect tableware as the glasses pass on a conveyor.
Tube End Inspection
By looking at the glass tubes from the ends after cutting, outside and inside diameter, wall thickness, out-of-round, siding and ovality can be measured with accuracies down to 5 microns.
Hot and Cold-end Container Inspection
A process management tool designed to aid operators and process control personnel in managing the quality of containers at the time of production.
Robot Sampling Station
The JLI Robot Sampling Station (RSS) is an ideal tool for any production where highly precise measurements are critical or regular sampling of the production is needed.
Moulded Parts Inspection
The JLI vision Moulded Parts Inspection System is a fully automated 100% inspection system that can be tailored to measure the dimensions and surface qualities that are critical.
Tablet Dispensers Inspection
The vision system inspects tablet dispensers to detect wrong colored tablets, broken or missing tablets, and missing or defective covers on the dispenser.
Needle Inspection
A system for precision measurements of details on needles. The system inspects a macro area of the needle tip, and detects dimensional errors and the surface of the needlepoint.
Character Reader
The JLI vision systems read the characters and compare each character to a taught pattern. By using advanced pattern matching algorithms the system will identify the characters.
Bar Length Gauge
The system detects when the bar is moved from the roller lane to the walking beams. Reference marks are used for calibration in every measurement cycle.
Slab Concast Inspection
The speed and dimensions of concast steel are normally measured mechanically. The JLI system eliminates the contact wheel and manual measurement procedures.
.jpg?width=3000&height=1974&name=Box%20inspection%20(1).jpg)
Box Inspection
After the boxes are filled and closed, the final packaged product must be inspected. Damaged or incorrectly closed boxes are not sellable.
Label Inspection
When labelling, it is necessary to inspect the final product. Labelling machines cannot operate fault free. Therefore manual inspection is used in this operation.
Plastic Lid Inspection
JLI’s plastic lid inspection system is a compact and portable stand alone unit. The system is 2. generation and have been developed to meet the high demands for the pharmaceutical industry.
Plastic Container Inspection
The system can be used for any type of plastic container production, including injection blow moulding, and employ up to nine high resolution industrial area scan.
Prefilled Syringes
The system enables detection of small chips and cracks in pre-filled syringes with full coverage of the syringe including areas such as plunger, plungerrod, labels and liquids.
Catheter Inspection
JLI’s pharmaceutical catheter inspection system is a compact unit that can be installed online/inline. The system is now second generation.
Bloom Cropping Inspection
The bloom cropping Inspection system covers the area at the shear and measures the distance from the shear to the end of the material.
Slab Gauge Inspection
The slab dimension systems are typically installed before the primary mill. At this location the system can be used to check the slab size before the first pass.
Rail Surface Inspection
Rails can be surface inspected and characters read. Using optical filtering images are enhanced making the rail visually appear as cold.
Crate Inspection
When beer and soft drink crates return to the brewery they are emptied and washed. To ensure that crates are fit for reuse, an inspection system can be installed after washing.
Print Inspection
This vision system inspects prints immediately after production. If any discrepancies are detected, the system can activate a reject mechanism.
Board Inspection
In the production of different types of boards e.g. acoustic boards with a punched pattern or shelves, sometimes a repeating defect may occur, such as pressure marks, dimensional error, or positioning.
Hollow Brick Inspection
In the production of hollow bricks, it is important that certain dimensions are within tolerance e.g., width, height, depth, and bow.
Brick Inspection
This vision system inspects prints immediately after production. If any discrepancies are detected, the system can activate a reject mechanism.